Balance |
Analytical Balance :
Rapid weighing short triangular beam analytical balance suitable for research Laboratories for precision work.
Technical Specification :
Beam : Triangular short beam gun metal alloy. The rider scale fitted
infront of the beam is provided with 100 notches with zero at the centre.
Knife edges &
Planes : Made of finest agate.
Arrestment : Vertical raising type.
Stand : All parts of brass.
Pans : Chromium plates, slightly concave inwards dia 7.5 cm.
Case : Teak-wood polished case with front slider and two side doors.
Base : Sunmica black board.
Maximum
Capacity : 200 gms
|
 |
Chemical Balance
: For use in colleges and Industrial Laboratories
Beam : Short beam of hard brass. The upper edge divided into 50 scales divisions
to each side. Each scale division representing 1/5 mg. Rider on the scale.
Stand : All parts of brass.
Arrestment : Vertical raising type.
Pans : Chromium plated, slightly concave inwards.
Case : Wooden polished case, with front slider and two side doors.
Base : Sunmica black board.
Capacity : 200gms
Sensitivity : 1/5 mg |
 |
|
Compression balance
Plastic case, slopping front, detachable rigid plastic load pan, krumbbled zero
adjusting control
Capacity 1Kg x 5gm 2Kg x 10gm 5Kg x 25gm 10Kg x 50gm |
 |
|
Dial balance |
 |
Digital balance
Multi capacity for selection, Capacity/Division: 3Kg/1g;5Kg/1g
Digital Scale,Auto zero setting tracking,Kg and oz conversion,Easy for operation,Long battery life, Auto power off,Easy calibration |
 |
Digital Balance
Multi capacity for selection, Capacity/Division: 3Kg/1g;5Kg/1g
Digital Scale,Auto zero setting tracking,Kg and oz conversion,Easy for operation,Long battery life, Auto power off,Easy calibration |
 |
Double pan balance
Twin pan balance for accurate and rapid weighing of masses up to 2 Kg when used with supplementary masses.
Technical Specification :
The balance has a cast alloy base and feature angled beams with center reading poises; undivided tare beam with a poise which slides and rotates for fine adjustment; spring loaded zero adjust compensator; precision ground knives and cross braced aluminum alloy box end beam.
Equipped with facility for under balance weighing.
Beams 0-200g X 10g, 0-10g X 0.1 g Tare 224 g
Pan, stainless steel, 150 mm diameter. |
 |
Lever arm balance
The dual range are scale 0-250 gms x 1gm division and 0-1 Kg x 10gms.
With removable pan. The changeover is effected by a swing over mass on the pointer arm. A hook is provided below the pan for relative density and upthrust determinations.
|
 |
Spring Balance
Spring Balances Metric : Flat form with hook and brass lacquered scale, Salter Design, Accurate.
Type A B C D E F G
Cap. (gms) 100 200 500 1000 2000 5000 10000
Sub Divided 1 2 5 10 20 50 100 |
 |
Triple beam balance
The balance has three notched weighing beams with center indicating sliding masses, giving total weighing capacity of 610gm. Additional masses are hung on the end of the beam increasing the capacity by upto 2610gm. and they can be stored in the recessed base when not required with magnetic damping for quick weighing. Pan, stainless steel, diameter 150mm
Beams : 0-500 g x 100g; 0-100g x 10g; 0-10g x 0.1g
Supplimentry masses 2 x 1000 gm & 1 x 500gm
|
|
Double Beam Balance :
Twin pan balance for accurate and rapid weighing of masses up to 2 Kg when used with supplementary masses.
Technical Specification :
The balance has a cast alloy base and feature angled beams with center reading poises; undivided tare beam with a poise which slides and rotates for fine adjustment; spring loaded zero adjust compensator; precision ground knives and cross braced aluminum alloy box end beam.
Equipped with facility for under balance weighing.
Beams 0-200g X 10g, 0-10g X 0.1 g Tare 224 g
Pan, stainless steel, 150 mm diameter. |
 |
Platform Balance :
Capacity 2010 Gms., Sensitivity 0.1g , Upper beam0-200g, 10g increment (lower beam) ,Tare capacity 200g (Optional)
Pan Diameter S.S. : 150 MM
|
 |
Mass Sets for Physical Balance :
Precision of chrome plated in1-2-5 series. Minor fractionals are of aluminium and major fractionals are of Brass, 10mg rider is nickelled, complete box to protect them from loss. Set is in polished wooden box.
Type A B C D Set of 1 g to 100 100g 200g 500g 1000g
|
 |
Slotted Weight Sets.
Our slotted weights are very qualitative and durable in nature and has a wide demand in the medical industry. As its physical feature, it comprises masses of brass with slots, brass hangers with hook and fine finish. Its masses can be both removable and replaceable on hanger.
|
 |
Knob Type Weight Set
We also offer our clientsthe knob type weight Set which os made of brazz and is avilable in the weight range of 1 gm. to 100 gms and also from 200 gms. to 2.0 Kgs. We also manufacture he heavy weight wegths for weight measurement with cast iron (Brass Plated).
|
 |
| |
|
